DIY Off-grid Solar House Kit - Small House 2.35 Kw with Super Powered Lithium Batteries.

MORE POWER, LONGER LASTING, LESS WEIGHT!  (Long term a better WH/$ investment)  Over 38 million watt hours over life of batteries!

HIGHEST QUALITY LiFePO4 LITHIUM BATTERIES PRODUCE AN INCREDIBLE 9600 Wh OF USABLE ENERGY!!  (Equivilant to 19,200 Wh AGM batteries which equates to 9.6 million watt hours over life of high quality AGM batteries.)


(8) Lithium Battery 12V 100Ah LiFePO4 Lithium Iron Phosphate


AIMS Power introduces its new battery product line of LiFePO4 batteries. The LiFePO4 batteries maintain constant output voltage, providing more efficient power. This allows the cell to deliver virtually full power until it is fully discharged without harming the battery, and it can greatly simplify or even eliminate the need for voltage regulation circuitry. The battery has a much longer cycle life capacity, and is easier to maintain compared to other battery technologies. The LiFePO4 technology has better thermal and chemical stability, which improves battery safety and packed with power in a small and lightweight footprint. Easily uses the same space as your existing 12V battery and replaces lead acid,
AGM or Gel battery applications in RVs, boats,
commercial vehicles, off grid back up power and
much more. 

4000+ cycles 10 year warranty. 

Note: These batteries replace the (16) AGM batteries that usually come with the kit.

Features:

• Extremely high number of charge/discharge cycles
• > 10 Year lifespan with proper maintenance
• Wide operating temperature range
• Unsurpassed high temperature performance
• Green energy without metal contaminant
• Low maintenance
• High amp capacity
• Stable output voltage
• Little self-discharge
• BMS safety protection. Each cell is fused and if for some unlikely situation a cell fails, this design will isolate the cell stopping any other damage and allows the battery to function safely
• Convenient removable carry handle
• Lightweight
• 50, 100 & 200 Ah models available
• Short circuit protected
• Physical damage to battery case will not cause fire
• Excessive thermal exposure will not cause a fire
• Able to withstand over-charge/over-discharge without damage to the battery
• Sophisticated Battery Management System (BMS)

SPECIFICATIONS FOR EACH 100Ah battery:   (There are 8 of these in this Upgrade kit and are wired to produce 48 volt system)

Electrical Specifications	LFP12V100A
Nominal Voltage	12.8V
Nominal Capacity (at .5C, 77°F)	100Ah
Minimum Capacity (at .5C, 77°F)	95Ah
Expected Cycle Life	>4000 cycles w/1C charge and discharge rate, at 77°F, 80% DOD
Operating Specifications
Charge Method	Smart charger, constant current, constant voltage
Charge Voltage Range (Max 14.6V)	14.4 -14.6V
Continuous Charge Current	100A Max
Charge Temperature	32° F to 113° F
Continuous Discharge Current	100A Max
Peak Instant Discharge Current (10 secs)	200A
Over Voltage Shutdown	15.6 +/-.2V
Discharge Cut-off Voltage	8V =/- .5V
Discharge Temperature	-4° F to 149° F
Storage Temperature	-4° F to 113° F
Self Disharge (stored at 50% SOC)	< 3%/month
Watt hours	1200 watt hours
Physical Specifications
Battery Dimensions	12.75″L x 6.5″W x 8.75″H
Weight	30.2 lb
Shipping Weight	32 lb
Group Size	31
Battery post size	5/16″
BMS Operation
Over Charge Protection	Over charge detection voltage:   3.9 +/- .05V
	Over charge detection delay time:   .96 – 1.4s
	Over charge release voltage:   3.80 +/-.05V
	Maximum charge voltage:   3.65 +/-.05V
Over Discharge Protection	Over discharge detection voltage:   2.0V +/- .05V
	Over discharge detection delay time:   115-173ms
	Over discharge release voltage:   2.3V +/- .10V
Over Current Protection	Over current detection delay time:   9 +/- 2ms
	Over current release condition:   Cut load
Polarity Reverse Protection	Yes
Short Circuit Protection	Yes
UPC	840271004587
Warranty	10 Yr Manufacturer Defect

................................


FREE SHIPPING! (anywhere in continental US)

Comes complete with:

• 1 - 10,000 watt 48 volt Pure-Sine low frequency inverter with 110/220Vac Split Phase
• 10 - 235 watt polycrystalline solar panels for a total output of 2350 watts
• 8 - 100 Ah 12 volt sealed LiFePO4 Lithium Iron Phosphat Batteries for Longer Life, More Power, Lighter Weight
• 1 - 80 Amp 48 volt MPPT Multi stage smart solar charge controllers
• 1 - Xantrex Power Distribution box with 250 amp battery shut off breaker
• 1 - 6 breaker Combiner box with (5) 15 Amp breakers installed
• 50 feet of solar panel cable per panel and all associated cables (see details in cable specifications below)       

*Easily expandable!!   Just add more batteries, solar panels, charge controllers.
**Upgrade to a 12,000 watt inverter for only $150!

**ADD A 2000 WATT BACKUP WIND SYSTEM TO YOUR SOLAR SYSTEM FOR ONLY $4895!

 (Cash or check preferred.  Credit Card purchases will be charged a processing fee of $500.)

Remember… Federal and State tax credits/deductions can pay for 50%-70% of the cost of the system. http://www.dsireusa.org/

This unique 48 volt system is simply superior in design and quality. It’s for those people who want a DIY complete solar system kit they can put on their cabin, house, or trailer to become completely energy independent. Designed to have solar panels and batteries easily added later for even more power.

---

Component features and specifications outlined below.

Inverter

Built with a 48 volt DC input, this inverter performs with very little power loss. Users receive a notable increase in efficiency in large systems when compared to using 12 or 24 volts, which can be an attractive feature for sustainability lovers looking to live as efficiently as possible.

The most common use for this inverter is emergency backup power in homes, business and recreation locations. You’ll always be prepared for the next power outage with access to 10000 watts of continuous power and 30,000 watts of surge (for up to 20 seconds).

One of the most sought-after features this inverter has is the direct-connect terminal block, which allows users to surpass the 10000 watt capacity and harness its 300% surge power (up to 30,000 watts for 20 seconds as previously stated).

It’s also built to withstand reasonable heat and temperature fluctuations because of its over-temperature protection and dual thermally-controlled fans.  And it’s protected from humidity or dust and dirt by virtue of its marine-coated or “conformal-coated” boards. This inverter provides the reliability needed in any business or residential emergency backup power applications.

Features:
 

10000 watt low frequency inverter 110/220Vac Split Phase

30000 watt surge for 20 seconds -3x surge capability

Battery Priority Selector

Terminal Block

Marine Coated and Protected

Multi Stage Smart charger 100 Amp

remote panel available

10msec typical transfer time

selectable 25W power save mode (hibernation)

8 battery charger settings

Inverter Specifications

Output Specifications:

Continuous Output Power:	10000 Watts
Surge Rating:	30000 Watts (20 Seconds)
Output Waveform:	Pure Sine/Same as input (Bypass Mode)
100-110-120Vac / 220-230-240Vac
Nominal Efficiency:	>88% (Peak)
Line Mode Efficiency:	>95%
Output Frequency:	50Hz +/- 0.3Hz / 60Hz +/- 0.3Hz
Typical Transfer Time:	10ms (Max)
THD:	< 10% DC

 

Input Specifications:

Nominal Input Voltage:	48.0Vdc
Low Battery Alarm:	42.0Vdc-44.0Vdc
Low battery Trip:	40.0Vdc-42.0Vdc
High Voltage Alarm:	64.0Vdc
Low battery Voltage Restart:	62.0Vdc
Idle Consumption:	150 Watts
Power Saver Mode Idle Consumption:	35 Watts

Charger Specifications
 

Output voltage:	Depends on battery Type
Charger Rate:	100A

Dimensions 
 

Unit Weight:	145.5 lbs.                         (66 kg)
Unit Size L x W x H:	23.3 x 16.3 x 7.9 inches     (592mm x 414mm x 201mm)
Shipping Weight:	190 lbs.                             (86.2 kg)
Shipping L x W x H:	30 x 21.25 x 15.25 inches   (762mm x 540mm x 387.4mm)

 

---

Batteries

Battery specifications: Centennial CB12-120S (12V118.6Ah)

Cells Per Battery	6
Voltage Per Battery	12
Capacity	115Ah @ 10 hr-rate to 1.80V per cell 118.6Ah @ 20 hr-rate to 1.75V per cell
Weight	Approx. 68.78 Lbs/31.2 Kg (Tolerance +/- 2 %)
Dimensions	12.99" (Length) x 6.77" (Width) x 9.51" (High) 330mm (Length) x 172mm (Width) x 241.5mm (High)
Max. Discharge Current	1150A (5 sec)
Internal Resistance	Approx. 4.2 m Ω
Operating Temperature Range	Discharge: -4°F ~ 140°F / -20°C ~ 60°C Charge:     32°F ~ 122°F / 0°C ~ 50°C Storage:    -4°F ~ 140°F / -20°C ~ 60°C
Normal Operating Temperature Range	77°F ± 9°F / 25°C ± 5°C
Float charging Voltage	13.6 TO 13.8 VDC / battery Average at 77°F / 25°C
Recommended Maximum Charging Current	34.5A
Equalization and Cycle Service	14.6 to 14.8 VDC/battery Average at 77°F / 25°C
Self Discharge (How quickly the stored energy will deplete when not in use)	CB Valve Regulated Lead Acid (VRLA) batteries can be stored for more than 6 months at 77°F / 25°C. Self-discharge ratio less than 3% per month at 77°F / 25°C. Please charge batteries before using.

 
16 batteries with a capacity of 120 amp hr each.. These are no maintenance batteries. They don't leak liquid, gas nor do they need to be vented. The only requirement is that they need to be charged regularly in order to maintain cell integrity of the battery. Charging every three to four weeks is recommended. Failure to ensure a high enough voltage, through consistent charging, will result in cell degradation which causes irreparable damage to the battery.

---

Solar Panels
                                                                                 

Specifications

Model No.

CS6P-235PX

WARRANTY

Power Warranty	25 Years of 80% Output Power
Product Warranty	10 Years

ELECTRICAL DATA AT STC (Standard Test Conditions)

Maximum Power (Pmax)	235 W
Voltage at Maximum Power (Vmpp)	29.8 V
Current at Maximum Power (Impp)	7.90 A
Open Circuit Voltage (Voc)	36.9 V
Short Circuit Current (Isc)	8.46 A
Panel Efficiency	14.61 %
Power Tolerance (Positive)	0 ~ + 5 W

ELECTRICAL DATA AT NOCT (Nominal Operating Cell Temperature)

Maximum Power (Pmax)	170 W
Voltage at Maximum Power (Vmpp)	27.2 V
Current at Maximum Power (Impp)	6.27 A
Open Circuit Voltage (Voc)	33.9 V
Short Circuit Current (Isc)	6.86 A
Temperature	113 °F ± 3.6 °F / 45 ± 2 °C

THERMAL RATINGS

Operating Temperature Range	-40 °F ~ 185 °F / -40 ~ 85 °C
Temperature Coefficient of Pmax	-0.45 %/°C
Temperature Coefficient of Voc	-0.33 %/°C
Temperature Coefficient of Isc	0.06 %/°C

MAXIMUM RATINGS

Maximum System Voltage	600 V
Series Fuse Rating	15 A

MATERIAL DATA

Panel Dimension (H/W/D)	64 1/2" x 38 5/8" x 1 9/16"  (1642 x 994 x 40mm)
Weight	44.1 lbs                            (20 kg)
Cell Type	Polycrystalline
Cell Size	6 1/8" x 6 1/8"                    (156 ×156mm)
Cell Number	60
Glass Type	Tempered, Anti-reflection Coating
Glass Thickness	3.2 mm
Encapsulant Type	EVA
Back Cover Type	TPT
Frame Type	Anodized Aluminium Alloy
Junction Box Diodes	3
Junction Box Protection Class	IP 65
Connector Type	MC4
Cable Crosssection	4 mm2
Cable Length	39.37"                                 (1000mm)

 

---

Solar Charge Controller
80 amp 48V MPPT Solar multi stage smart charge controller
      
Specifications

Nominal Battery Voltages	12, 24, 36, 48, or 60 VDC (Single model - selectable via field programming at start-up)
Maximum Output Current	80 amps @ 104°F (40°C) with adjustable current limit
PV Open Circuit Voltage (VOC)	150 VDC absolute maximum coldest conditions /    145 VDC start-up and operating maximum
Standby Power Consumption	Less than 1 Watt typical
Power Conversion Efficiency	97.5% @ 60 Amps in, at 48 VDC System voltage - Typical
Charging Regulation	Five stages: Bulk, Absorption, Float, Silent and Equalization
Voltage Regulation Set Points	10 to 80 VDC; user adjustable with password protection
Equalization Charging	Programmable Voltage Setpoint and Duration - Automatic Termination when completed
Battery Temperature Compensation	Automatic with optional RTS installed / 5.0 mV per °C per 2V battery cell
Voltage Step-Down Capability	Can charge a lower voltage battery from a higher voltage PV array - Max 150 VDC input
Programmable Auxilliary Control Output	12 VDC output signal which can be programmed for different control applications (Maximum of 0.2 amps DC)
Status Display	3.1" (8 cm) backlit LCD screen - 4 lines with 80 alphanumeric characters total
Remote Display and Controller (Optional)	Mate or Mate2 with RS232 Serial Communications Port
Network Cabelling	Proprietary network system using RJ 45 Modular Connectors with CAT 5e Cable (8 wires)
Data Logging	Last 128 days of Operation - Amp Hours, Watt Hours, Time in Float, Peak Watts, Amps, Solar Array Voltage, Max Battery Voltage Min Battery Voltage and Absorb for each day along with total Accumulated Amp Hours, and kW Hours of production
Positive Ground Applications	Requires two Pole Breakers for switching both positive and Negative Conductors on both Solar Array and Battery Connections (HUB-4 and HUB-10 cannot be used for use in positive ground applications)
Operating Temperature Range	Minimum -40°F to maximum 140° F (Power capacity of the controller is automatically de-rated when operated above 104° F)
Environmental Rating	Indoor Type 1
Conduit Knockouts	One 1" (35mm)on the back; One 1" (35mm) on the left side;Two 1" (35mm) on the bottom
Weight - Unit	12.35 Lbs.                 (5.6 kg)
Weight - Shipping	13.89 Lbs.                 (6.3 kg)
Dimensions - Unit	17.33" x 5.52" x 3.94" (44 x 14 x 10 cm)
Dimensions - Shipping	20.1" x 9.45" x 8.47"   (51 x 24 x 21.5 cm)
Options	Remote Temperature Sensor (RTS), HUB 4,HUB 10, MATE, MATE 2
Menu Languages	English & Spanish

 

---

POWER DISTRIBUTION BOX

Xantrex XW Series Power Distribution Panel (PDP)

                                                               
 

Dimensions (H x W x D)	30 x 16 x 8.3 in   (761 x 406 x 210 mm)
Shipping dimensions (H x W x D)	48 x 21 x 3.5 in   (1220 x 533 x 343 mm)
Shipping weight	67.2 Lbs.            (30.5 kg)
Included	XW+ PDP enclosure with a field-reversible panel door, includes wall mount bracket, and XW+ Conduit Box
	(3) 60 A, 120/240 Vac, two-pole Square-D, type QOU, DIN-rail mounted AC breakers for AC input, bypass and AC load (factory-installed), plus five AC breaker expansion positions
	One GJ 250A 160 Vdc, 3/8” stud DC breaker installed, plus two expansion positions
	Eight expansion positions for charge controller DC breakers (Note: XW supports up to 4 MPPT 80 600 or 4 MPPT 60 150 charge controllers)
	One ground terminal bus bar, one neutral terminal bus bar and one battery negative terminal bus bar
	One pair #4/0 AWG Arctic Ultraflex Blue™ battery cables (factory installed and labeled, ready to connect)
	#6 AWG Arctic Ultraflex Blue™ AC wiring (factory installed and labeled, ready to connect)

 

---

Combiner Box

 
Midnite Solar MNPV6 Combiner Box
 

Aluminum rainproof type 3R enclosure

Internal plastic injection molded dead front cover

Knock outs that accept waterproof strain reliefs, conduit or panel mount MC type connectors

Knock outs for lightning arrestors

Uses 150 VDC breakers

ETL listed to UL1741 for use in the US and Canada

 

Specifications
 

Max VDC	150
Max # of Input Circuits	6
PV Source Circuits - Max OCPD Rating Amps	20
PV Source Circuits - OCPD	CB 150V
PV Source Circuits - Wire Range AWG	14 - 6
PV Output Circuits - Max # of Output Circuits	2
PV Output Circuits - Max Cont. Current Amps	120
PV Output Circuits - Wire Range AWG	14 - 1/0
Approved Mounting Orientation	90° to 14°
Enclosure Type/Material	3R/Alum
Listing	UL1741

 

---

Cables and Wires

• 50 feet of 10 AWG Insulated PV wire is allocated per panel with wire shipped in 500 - 1000 foot long rolls, depending on number of solar panels requiring connection. This is done to ensure you get the right length wire for your set up. Instructions for attaching MC4 Connector end and the tool required are also provided.
• 10 feet of black and 10 feet of red 6 AWG cable is provided for connections from combiner box to solar charge controller
• 10 feet of black and 10 feet of red 6 AWG cable is provided for connections from solar charge controller to PDP
• 10 feet of black and 10 feet of red 4/0 AWG cable provided for connections from PDP to batteries
• 10 feet of black and 10 feet of red 4/0 AWG cable provided for connections from PDP to Inverter
• 6 cables @ 24 inches and 1/0 AWG provided for battery bank connections
• 12 cables @ 18 inches and 2 AWG provided for battery bank connections

 

The TOTAL SOLAR 10,000w Small House Kit is a complete full solar energy house system. This system can power a small sized house as is.
EASILY EXPANDABLE!! Simply add more panels, batteries, controllers for larger loads.
(Kit does not include mounting system for solar panels. We can send you instructions on how to install system, and how to use low cost materials from your local hardware store to make a professional looking solar panel mount for your roof or ground.

Call us for a free consultation on your power needs and installation concepts for your particular installation.)

Phone: 208-745-7100
Email: support@totalsolar.us

Optional Extra

LCD Remote for more convenient ability to switch on Inverter.

Features:
• Battery Voltage
• AC input Voltage
• AC Output Voltage
• Frequency Monitoring
• Load Percentage Monitoring
• 60 foot connection cable

Dims: 5 1/2"L x 1 1/4"H x 4 1/4"W