Diy Kit - Master House 12.2Kw
A COMPLETE MASTER HOUSE SOLAR AND LITHIUM BATTERY DIY KIT SYSTEM FOR AN INCREDIBLE PRICE!
with Internet/WiFi hookup, allows you to monitor system performance from via internet from anywhere.
Comes complete with:
- 1 - 12,000 watt 48 volt low frequency inverter with 110/220Vac Split Phase
- 48 - 250 watt polycrystalline solar panels for a total output of 12,000 watts
- 12 - 48 volt sealed Lithium batteries that are the equivilant of (48) 12v 100ahr Lithium batteries for 48 Kwh of stored energy
- 6 - 80 Amp 48 volt MPPT Multi stage smart solar charge controllers w wifi
- 2 - Xantrex Power Distribution boxes with 250 amp battery shut off breakers
- 4 - Combiner boxes and 24 required 15 Amp breakers + master breakers
- All associated cables (see details in cable specifications below)
*Easily expandable!! just add more batteries, solar panels, charge controllers.
**ADD A 2000 WATT BACKUP WIND SYSTEM TO YOUR SOLAR SYSTEM FOR ONLY $5895!
Federal and State tax credits/deductions can pay for 50%-70% of the cost of the system. http://www.dsireusa.org/
Cash or check preferred. Credit Cards purchases will be charged a fee of 3.5%.)
This unique 48 volt system is superior in design and quality. It’s for those people who want a DIY complete solar system kit that they can power their cabin or house to become completely energy independent. Designed to have solar panels and batteries easily added later for even more power needs.

Component features and specifications outlined below.
Inverter

Features:
12000 watt low frequency inverter 110/220Vac Split Phase |
36000 watt surge for 20 seconds -3x surge capability |
Battery Priority Selector |
Terminal Block |
Marine Coated and Protected |
Multi Stage Smart charger 120 Amp |
remote panel available |
10msec typical transfer time |
selectable 25W power save mode (hibernation) |
8 battery charger settings |
Inverter Specifications
Output Specifications:
Continuous Output Power: |
12000 Watts |
Surge Rating: |
36000 Watts (20 Seconds) |
Output Waveform: |
Pure Sine/Same as input (Bypass Mode) |
100-110-120Vac / 220-230-240Vac |
|
Nominal Efficiency: |
>88% (Peak) |
Line Mode Efficiency: |
>95% |
Output Frequency: |
50Hz +/- 0.3Hz / 60Hz +/- 0.3Hz |
Typical Transfer Time: |
10ms (Max) |
THD: |
< 10% DC |
Input Specifications:
Nominal Input Voltage: |
48.0Vdc |
Low Battery Alarm: |
42.0Vdc-44.0Vdc |
Low battery Trip: |
40.0Vdc-42.0Vdc |
High Voltage Alarm: |
64.0Vdc |
Low battery Voltage Restart: |
62.0Vdc |
Idle Consumption: |
200 Watts |
Power Saver Mode Idle Consumption: |
40 Watts |
Charger Specifications
Output voltage: |
Depends on battery Type |
Charger Rate: |
120A |
Dimensions
Unit Weight: |
174 lbs. (78.93 kg) |
Unit Size L x W x H: |
23.3 x 16.3 x 7.9 inches (592mm x 414mm x 201mm) |
Shipping Weight: |
200 lbs. (90.72 kg) |
Shipping L x W x H: |
30 x 21.25 x 15.25 inches (762mm x 540mm x 387.4mm) |
LITHIUM BATTERY
SAVING $$ + Time! This New 48v Lithium Powerhouse is the equivilant of 64 AGM 12v 120ahr batteries over the life expectancy of each battery type at less than 1/2 the $$ cost!
This 48 Volt 150 AMP lithium iron phosphate (LiFePO4) industrial deep cycle battery is packed with power. The battery delivers efficient power for battery systems requiring large amounts of power at 48 Volts. The AIMS Power 48V 150 amp has large amp capacity in one battery and eliminates the need for

multiple batteries without losing amperage. Compared to other battery technologies, this battery delivers large amounts of power, at half the weight and provides up to 8 times more battery cycles and no memory problems. Loaded with automatic safety features, such as a Battery Management System (BMS), which maintains individual cell integrity, low and high voltage protections, reverse polarity and temperature management. The battery also uses automatic cell balancing, requires almost no maintenance and includes RS485 and CAN monitoring.
- 8 times more cycles compared to other battery technologies
- 3500 cycles at 80% DoD, 6000 cycles at 60% DoD
- Short circuit protection
- Automatic low voltage shutdown
- Over charge protection

- Over discharge protection
- Mount in any orientation
- Multiple batteries: 10 batteries in parallel maximum
- Automatic cell balancing
- High output current for inverters
- Battery status LED located on the front of the battery displays SOC percentage RS485 & CAN ports
- Power switch
- Built in Battery Management System (BMS)
- Reverse polarity protection (caution)
- No venting or gassing
- BMS temperature protection
Battery Management System: The built in BMS is a central hub inside the battery that maintains constant voltage, current and temperature. The BMS allows for maximum charging capacity for faster charging and efficient discharging. It also communicates with the desktop monitoring software via the RS485 or CAN port.
- 48Volt

- Lithium Iron Phosphate – LiFePO4
- 150 amps
- Battery status LED State of Charge display
- On/off switch
- 3/8 terminals
- Terminal covers included
- Cables included used for parallel connecting batteries – 41″ length
- Dimensions: 32″L x 21″W x 7″H
- Shipped dimensions: 38″L x 29″W x 21 1/2″H
- Unit weight: 184 lb
- Shipped weight: 242 lb
Batteries
Solar Panels
Specifications
WARRANTY
Power Warranty |
25 Years of 80% Output Power |
Product Warranty |
10 Years |
ELECTRICAL DATA AT STC (Standard Test Conditions)
Maximum Power (Pmax) |
235 W |
Voltage at Maximum Power (Vmpp) |
29.8 V |
Current at Maximum Power (Impp) |
7.90 A |
Open Circuit Voltage (Voc) |
36.9 V |
Short Circuit Current (Isc) |
8.46 A |
Panel Efficiency |
14.61 % |
Power Tolerance (Positive) |
0 ~ + 5 W |
*Standard Test Conditions (STC): air mass AM 1.5, irradiance 1000W/m2, cell temperature 25°C
ELECTRICAL DATA AT NOCT (Nominal Operating Cell Temperature)
Maximum Power (Pmax) |
170 W |
Voltage at Maximum Power (Vmpp) |
27.2 V |
Current at Maximum Power (Impp) |
6.27 A |
Open Circuit Voltage (Voc) |
33.9 V |
Short Circuit Current (Isc) |
6.86 A |
Temperature |
113 °F ± 3.6 °F / 45 ± 2 °C |
Nominal Operating Cell Temperature (NOCT): 800W/m2, AM 1.5, windspeed 1m/s,ambient temperature 20°C
THERMAL RATINGS
Operating Temperature Range |
-40 °F ~ 185 °F / -40 ~ 85 °C |
Temperature Coefficient of Pmax |
-0.45 %/°C |
Temperature Coefficient of Voc |
-0.33 %/°C |
Temperature Coefficient of Isc |
0.06 %/°C |
MAXIMUM RATINGS
Maximum System Voltage |
600 V |
Series Fuse Rating |
15 A |
MATERIAL DATA
Panel Dimension (H/W/D) |
64 1/2" x 38 5/8" x 1 9/16" (1642 x 994 x 40mm) |
Weight |
44.1 lbs (20 kg) |
Cell Type |
Polycrystalline |
Cell Size |
6 1/8" x 6 1/8" (156 ×156mm) |
Cell Number |
60 |
Glass Type |
Tempered, Anti-reflection Coating |
Glass Thickness |
3.2 mm |
Encapsulant Type |
EVA |
Back Cover Type |
TPT |
Frame Type |
Anodized Aluminium Alloy |
Junction Box Diodes |
3 |
Junction Box Protection Class |
IP 65 |
Connector Type |
MC4 |
Cable Crosssection |
4 mm2 |
Cable Length |
39.37" (1000mm) |
Solar Charge Controller
80 amp 48V MPPT Solar multi stage smart charge controller

Specifications
Nominal Battery Voltages |
12, 24, 36, 48, or 60 VDC (Single model - selectable via field programming at start-up) |
Maximum Output Current |
80 amps @ 104°F (40°C) with adjustable current limit
|
PV Open Circuit Voltage (VOC) |
150 VDC absolute maximum coldest conditions / 145 VDC start-up and operating maximum |
Standby Power Consumption |
Less than 1 Watt typical |
Power Conversion Efficiency |
97.5% @ 60 Amps in, at 48 VDC System voltage - Typical |
Charging Regulation |
Five stages: Bulk, Absorption, Float, Silent and Equalization |
Voltage Regulation Set Points |
10 to 80 VDC; user adjustable with password protection |
Equalization Charging |
Programmable Voltage Setpoint and Duration - Automatic Termination when completed |
Battery Temperature Compensation |
Automatic with optional RTS installed / 5.0 mV per °C per 2V battery cell |
Voltage Step-Down Capability |
Can charge a lower voltage battery from a higher voltage PV array - Max 150 VDC input |
Programmable Auxilliary Control Output |
12 VDC output signal which can be programmed for different control applications (Maximum of 0.2 amps DC) |
Status Display |
3.1" (8 cm) backlit LCD screen - 4 lines with 80 alphanumeric characters total |
Remote Display and Controller (Optional) |
Mate or Mate2 with RS232 Serial Communications Port |
Network Cabelling |
Proprietary network system using RJ 45 Modular Connectors with CAT 5e Cable (8 wires) |
Data Logging |
Last 128 days of Operation - Amp Hours, Watt Hours, Time in Float, Peak Watts, Amps, Solar Array Voltage, Max Battery Voltage Min Battery Voltage and Absorb for each day along with total Accumulated Amp Hours, and kW Hours of production |
Positive Ground Applications |
Requires two Pole Breakers for switching both positive and Negative Conductors on both Solar Array and Battery Connections (HUB-4 and HUB-10 cannot be used for use in positive ground applications) |
Operating Temperature Range |
Minimum -40°F to maximum 140° F (Power capacity of the controller is automatically de-rated when operated above 104° F) |
Environmental Rating |
Indoor Type 1 |
Conduit Knockouts |
One 1" (35mm)on the back; One 1" (35mm) on the left side;Two 1" (35mm) on the bottom |
Weight - Unit |
12.35 Lbs. (5.6 kg) |
Weight - Shipping |
13.89 Lbs. (6.3 kg) |
Dimensions - Unit |
17.33" x 5.52" x 3.94" (44 x 14 x 10 cm) |
Dimensions - Shipping |
20.1" x 9.45" x 8.47" (51 x 24 x 21.5 cm) |
Options |
Remote Temperature Sensor (RTS), HUB 4,HUB 10, MATE, MATE 2 |
Menu Languages |
English & Spanish |
POWER DISTRIBUTION BOX
Xantrex XW Series Power Distribution Panel (PDP)
Dimensions (H x W x D) |
30 x 16 x 8.3 in (761 x 406 x 210 mm) |
Shipping dimensions (H x W x D) |
48 x 21 x 3.5 in (1220 x 533 x 343 mm) |
Shipping weight |
67.2 Lbs. (30.5 kg) |
Included |
XW+ PDP enclosure with a field-reversible panel door, includes wall mount bracket, and XW+ Conduit Box |
|
(3) 60 A, 120/240 Vac, two-pole Square-D, type QOU, DIN-rail mounted AC breakers for AC input, bypass and
AC load (factory-installed), plus five AC breaker expansion positions |
|
One GJ 250A 160 Vdc, 3/8” stud DC breaker installed, plus two expansion positions |
|
Eight expansion positions for charge controller DC breakers (Note: XW supports up to 4 MPPT 80 600 or 4 MPPT 60 150 charge controllers) |
|
One ground terminal bus bar, one neutral terminal bus bar and one battery negative terminal bus bar |
|
One pair #4/0 AWG Arctic Ultraflex Blue™ battery cables (factory installed and labeled, ready to connect) |
|
#6 AWG Arctic Ultraflex Blue™ AC wiring (factory installed and labeled, ready to connect) |
Midnite Solar MNPV12 Combiner Box

Aluminum rainproof type 3R enclosure |
Internal plastic injection molded dead front cover |
Knock outs that accept waterproof strain reliefs, conduit or panel mount MC type connectors |
Knock outs for lightning arrestors |
Uses 150 VDC breakers |
ETL listed to UL1741 for use in the US and Canada |
Specifications
Max VDC |
150 |
Max # of Input Circuits |
12 |
PV Source Circuits - Max OCPD Rating Amps |
30 |
PV Source Circuits - OCPD |
CB 150V |
PV Source Circuits - Wire Range AWG |
14 - 6 |
PV Output Circuits - Max # of Output Circuits |
2 |
PV Output Circuits - Max Cont. Current Amps |
200 |
PV Output Circuits - Wire Range AWG |
14 - 2/0 |
Approved Mounting Orientation |
90° to 14°
|
Enclosure Type/Material |
3R/Alum |
Listing |
UL1741 |
Midnite Solar MNPV6 Combiner Box

Aluminum rainproof type 3R enclosure |
Internal plastic injection molded dead front cover |
Knock outs that accept waterproof strain reliefs, conduit or panel mount MC type connectors |
Knock outs for lightning arrestors |
Uses 150 VDC breakers |
ETL listed to UL1741 for use in the US and Canada |
Specifications
Max VDC |
150 |
Max # of Input Circuits |
6 |
PV Source Circuits - Max OCPD Rating Amps |
20 |
PV Source Circuits - OCPD |
CB 150V |
PV Source Circuits - Wire Range AWG |
14 - 6 |
PV Output Circuits - Max # of Output Circuits |
2 |
PV Output Circuits - Max Cont. Current Amps |
120 |
PV Output Circuits - Wire Range AWG |
14 - 1/0 |
Approved Mounting Orientation |
90° to 14°
|
Enclosure Type/Material |
3R/Alum |
Listing |
UL1741 |
Cables and Wires
- 50 feet of 10 AWG Insulated PV wire is allocated per panel with wire shipped in 500 - 1000 foot long rolls, depending on number of solar panels requiring connection. This is done to ensure you get the right length wire for your set up. Instructions for attaching MC4 Connector end and the tool required are also provided.
- 10 feet of black and 10 feet of red 6 AWG cable is provided for connections from combiner boxes to solar charge controllers
- 10 feet of black and 10 feet of red 6 AWG cable is provided for connections from solar charge controllers to PDP
- 10 feet of black x 6 and 10 feet of red x 6 4/0 AWG cable provided for connections from PDP to batteries and Inverter
- 30 cables @ 24 inches and 1/0 AWG provided for battery bank connections
- 48 cables @ 18 inches and 2 AWG provided for battery bank connections
- MC4 Connectors
The TOTAL SOLAR 12,000w Master House Kit is a complete full solar energy house system. This system can power a larger sized house as is. EASILY EXPANDABLE!! Simply add more panels, batteries, controllers for larger loads.
(Kit Does not include mounting system for solar panels. We can send you instructions on how to install system, and how to use low cost materials from your local hardware store to make a professional looking solar panel mount for your roof or ground.)
Call us for a free consultation on your power needs and installation concepts for your particular installation.
Phone: 208-745-7100
Email: support@totalsolar.us
Optional Extra
LCD Remote for more convenient ability to switch on Inverter.

Features:
• Battery Voltage
• AC input Voltage
• AC Output Voltage
• Frequency Monitoring
• Load Percentage Monitoring
• 60 foot connection cable
Dims: 5 1/2"L x 1 1/4"H x 4 1/4"W